STUDY OF SOME ENGINEERING FACTORS CONCERNING THE PERFORMANCE OF THE AFFECTING TOOL IN CROP RESIDUES SHREDDER | ||
| Misr Journal of Agricultural Engineering | ||
| Article 35, Volume 27, Issue 4, October 2010, Pages 1555-1571 PDF (710.72 K) | ||
| Document Type: Original Article | ||
| DOI: 10.21608/mjae.2010.105064 | ||
| Authors | ||
| Ahmed El-Raie E. Suliman1; Gamal El-Deen Mohamed Nasr1; Magdy Ahmed Baiomy2; Abdelraouf Ramadan Eid3 | ||
| 1Prof. of Agric. Eng , Fac. of Agric., Cairo Univ., Egypt. | ||
| 2Senior Res., Agric. Eng. Res.Inst.(AEnRI) Agric. Research Center, Egypt. | ||
| 3Researcher at Water Relations and Field Irrigation Department, National Research Center – Dokki – Giza- Egypt. | ||
| Abstract | ||
| The aim of present work is improving the performance of the crop residues shredder by study of some engineering factors concerning the performance of the affecting tool. The items to achieve the aim of the present study are:(1) Evaluation of shredder performance before development(2)Manufacture of cutting knives from local materials.(3)Shredder performance analysis in cutting of cotton stalks (4)Shredder performance analysis in cutting of rice straw (5)Cost analysis of cutting operation. From the above mentioned study, it can recommend the following points for farmer or producer or user following the mentioned order has all the choices according to the prevailing production conditions;1- The proper selection of new material leads to decrease the sharp edge angle of modified knives to 20o degree without deformation. 2- Maximum cutting efficiency for cotton stalks was 86.4 % at 1mm clearance distance.,20o degree knife edge angle and 1600 rpm cutting drum speed.3- Minimum fuel consumption rate for cotton stalks was 2.48 L/h at 1 mm clearance distance, 20o degree knife edge angle. 4- Maximum machine production for cotton stalks was 1.4 ton/h at following factors:5 mm clearance distance, at 20o degree knife edge angle and 1600 rpm cutting drum speed.5- Maximum cutting efficiency for rice straw was 45.6 % at 1 mm clearance distance.,20o degree knife edge angle ,1600 rpm cutting drum speed. 6- Minimum fuel consumption rate for rice straw was 3.51 L/h at 1 mm clearance distance, 20o degree knife edge angle.7-Maximum machine production for rice straw was 0.99ton/h at following factors: 1 mm clearance distance.,20o degree knife edge angle 1600 rpm cutting drum speed.8-Cutting operation cost is 27.5 L.E./h. | ||
| References | ||
|
Arif, El. M. (1999). Development and performance evaluation of a shredder machine for composting. Ph.D. thesis, Agricultural Mechanization Department. Faculty of Agriculture, Ain Shams University.
Chattopadhay P.S. and K.P. Pandey (1992). Experimental verification of impact cutting energy estimated through mathematical modeling. Agric. Mechanization in ASIA 23 (3) 39-42.
El-Awady, M.N.(1978). Engineering of tractors and Agricultural Machinery. Text book. Col.Ag. Ain-Shams Univ., 5th Ed.,:164-167.
Habib, R.A.(2002). Designand performance of cutting tools of chopping Machines of Agricultural Crop residues. Ph.D. Thesis, Mechanicaldesign and production Dept. Fac. of Eng. Cairo Univ.
Hashish, A. E.(1981). A study for machine for crushing and grinding crop residue J. Approp, Technol for Egypt Agr. Small. Agric. Activist min of agric USAID No. 2: 15-32.
Ige, M.T., and M.F.Finner (1976b). Optimization of the performance of cylinder type forage harvester cutterhead. Trans. ASAE, 19 (3) 455-460.
Imbabi, A.T. (2001). Field evaluation of combination unit for seed-bed preparation and planting wheat under Egyptian conditions. Misr J.Agric. 18 (2): 261-278.
Kepner. R.A., R. Bainer, and E.L. Barger (1987). Principals of farm machinery, 3d Ed., Avi- Pub. Co. : 315-318.
Prasad, T. and Gupta, C.P. (2005). Mechanical properites of maize stalk as related to harvesting. Jagric Engng Res., 20 (1) 79-87.
Sverker, P. (1987). Mechanics of cutting plant material, An ASAE Monograph numbers 7 in a series published by American Society of Agricultural Engineering.
Yumnam, J., and S. Pratap (1991). Energetic of forage chopping. AMA vol. 22 No. 1, p59-63.
الإدارة المرکزیة للاقتصاد الزراعی . )2009(. تقدیرات المحاصیل الزراعیة والمخلفات. وزارة الزراعة واستصلاح الأراضی - جمهوریة مصر العربیة. | ||
|
Statistics Article View: 228 PDF Download: 310 |
||
