FACTORS INFLUENCING THE QUALITY OF EXTRUDED SINKING AQUATIC FEED PELLETS | ||
| Misr Journal of Agricultural Engineering | ||
| Article 59, Volume 27, Issue 4, October 2010, Pages 1953-1982 PDF (1017.34 K) | ||
| Document Type: Original Article | ||
| DOI: 10.21608/mjae.2010.105385 | ||
| Authors | ||
| O. Kaddour1; S. Alavi2; K. Behnke3 | ||
| 1Senior researcher- Agriculture Engineering Research Institute (AEnRI), Egypt. | ||
| 2Associate professor- Department of Grain Science & Industry, Kansas State Univ., Manhattan, KS 66506 Kansas State- USA | ||
| 3professor- Department of Grain Science & Industry, Kansas State Univ., Manhattan, KS 66506 Kansas State- USA | ||
| Abstract | ||
| Aquatic feed production is an important application of extrusion processing. This study focused on the effect of formulation particle size and processing parameters on physical and stability characteristics of extruded sinking shrimp feed. The parameters studied were ration particle size (0.8 and 1.2 mm), single screw extrusion die profile (land length of 2.5 and 5.0 mm; die output area percentage of 4.5 and 6.7%), and drying conditions (cooling only and drying followed by cooling). The single screw extruder die L/D ratio was 30: 1, with outlet diameter of 2.5 mm. The same formulation was also pelleted by a ring die pellet mill with die L/D ratio of 13.3: 1 and diameter of 2.38 mm, followed by only cooling of pellets. The quality of feed obtained by extrusion and pellet mill were evaluated. The optimum parameters for sinking feed production by extrusion were - formulation particle size of 0.8 mm, die profile with 5.0 mm land length and 6.7% die output area percentage, and drying for 10.5 min at 210oC followed by cooling for 5.5 min. The process and pellet quality data for these parameters were 213.2 kg/h production rate, 68.4 kJ/kg specific mechanical energy (SME), 529.4 kg/m3 pellet bulk density, 6.7% final moisture content, 99.8% pellet durability, 100% pellet sinking percentage after immersion for 21-24 h, and water stability of 100% after 30 min, 90% between 30–60 min and 80% between 1-24 h. The corresponding pellet mill results were 444.1 kg/h production rate, 23.9 kJ/kg SME, 658.3 kg/m3 bulk density, 98.4 % durability, 100 % sinking percentage after 45 min, and water stability of 40% after 15 min, 10% after 30 min and 0.0% after 1 h. Results indicated that SME was the most important factor affecting pellet quality, and better quality sinking aquatic feed could be produced using single screw extrusion processing as compared to pellet mill processing. PRACTICAL APPLICATION The manuscript make focus on the physical and mechanical factors of single screw extruder affecting the sinking aquatic feed pellets quality by studying the die holes profile , formula particle size and drying - cooling profile , the results are very important for extrusion industries to determine the optimum conditions of formula and extruder to produce high quality of pellets, the study used new measurements , it's very important for industries quality control such as the pellets water stability and sinking percentage | ||
| References | ||
|
BRIAN P.; P.E. STRAHM AND K.RAUSCH 2001. The Phase Transition Analyzer™ and its Impact on Extrusion Processing of Foodstuffs. 2001 ASAE Annual International MeetingSponsored by ASAE Sacramento Convention Center Sacramento, California, USA July 30-August 1, 2001.
CHINNASWAMY.R., AND HANNA,M.A. 1987. Nozzle dimension effects on the expansion of extrusion cooked corn starch. Journal of food science. 52(6):1746-1747
DVID, A. F.2003. Pelleting for Profit - Part 1. National Grain and Feed Association Volume 54, Number 6, November 13, 2003.
GILPIN A.S. T. J. HERRMAN, K. C. BEHNKE, AND F. J. FAIRCHILD 2002. Feed moisture, retention time, and steam as quality and energy utilization determinants in the pelleting process. 2002 American Society of Agricultural Engineers Vol. 18(3): 331–338.
HILL, B. AND D.A. PULKINEN. 1988. A study of factors affecting pellet durability and pelleing efficiency in the production of dehydrated alfalfa pellets. A special report, Saskatchewan Dehydrators Association, Tisdale, SK, Canada: 25.
JAMES H.TIDWELL, CARL D WEBSTER, DANIEL H YANCEY AND LOUIS R D’ABRAMO. 1993. Partial and total replacement of fish meal with soybean meal and distillers’ by-products in diets for pond culture of the fresh water prawn (Macrobrachium rosenbergii). Aquaculture, 118:119-130.
KIM,C.N., JOSEPH,A.M., AND JEFFERY,T.M. 1989. Properties of Extruded dried distillers grains (DDG) and flour blends. Journal of Food processing and preservation, 13: 219-231.
LARSEN, T.B., S. SOKHANSANJ, R.T. PATIL AND W.J. CRERAR. 1996. Breakage susceptibility studies on alfalfa and animal feed pellets. Canadian Agricultural Engineering 38(1): 21-24.
MERCIER,C.,P.LINKO, AND J.M.HARPER. 1989. Extrusion cooking. American Association of Cereal Chemists, Inc. St. Paul, Minnesota,USA.
NEHRU C.; K.A. ROSENTRATER AND K. MUTHUKUMARAPPAN. 2005. Utilization of Distillers ried Grains for Fish Feed by Extrusion Technology – A Review 2005 ASAE Annual International Meeting Sponsored by ASAE Tampa Convention Center Tampa, Florida 17 - 20 July 2005 .
NEHRU C; K.A. ROSENTRATER AND K. MUTHUKUMARAPPAN. 2005. Physical Properties of Extruded Tilapia Feed with Distiller Dried Grains with Solubles 2005 ASAE Annual International Meeting Sponsored by ASAE Tampa Convention Center Tampa, Florida 17 - 20 July 2005 .
TABIL, L.G. AND S. SOKHANSANJ. 1996. Process conditions affecting the physical quality of alfalfa pellets. American Society of Agricultural Engineers 12(3): 345-350.
VICTOR Y.W, RONALD R, ROSTAGI, DAVID J, SESSA AND PAUL B.BROWN.1994. Utilization of protein rich Ethanol Co-products from Corn in Tilapia Feed. JAOCS 71(9):1041 – 1043. | ||
|
Statistics Article View: 289 PDF Download: 347 |
||
