El-Sheikha, M., Mostafa, M., Abdel-Salam, M. (2008). HYDRAULIC SYSTEM MAINTENANCE. test, 25(4), 1184-1199. doi: 10.21608/mjae.2008.152378
M.A. El-Sheikha; M.A. Mostafa; M.S. Abdel-Salam. "HYDRAULIC SYSTEM MAINTENANCE". test, 25, 4, 2008, 1184-1199. doi: 10.21608/mjae.2008.152378
El-Sheikha, M., Mostafa, M., Abdel-Salam, M. (2008). 'HYDRAULIC SYSTEM MAINTENANCE', test, 25(4), pp. 1184-1199. doi: 10.21608/mjae.2008.152378
El-Sheikha, M., Mostafa, M., Abdel-Salam, M. HYDRAULIC SYSTEM MAINTENANCE. test, 2008; 25(4): 1184-1199. doi: 10.21608/mjae.2008.152378

HYDRAULIC SYSTEM MAINTENANCE

Misr Journal of Agricultural Engineering
Article 56, Volume 25, Issue 4, October 2008, Pages 1184-1199    PDF (384.7 K)
Document Type: Original Article
DOI: 10.21608/mjae.2008.152378
Authors
M.A. El-Sheikha1; M.A. Mostafa2; M.S. Abdel-Salam3
1Prof. of Agric Eng, Fac of Agric, Mansoura Univ., Egypt.
2Lec. of Agric Eng, Fac of Agric, Mansoura Univ., Egypt.
3Post graduate student of Agric Eng, Fac of Agric, Mansoura Univ., Egypt.
Abstract
 Any problem in a hydraulic system in any hydraulic equipment, while working, may decrease the investment to outweigh the cost of maintenance or reconstruction. The hydraulic cylinder is a main component in the hydraulic systems. In most cases of forced stop, the equipment malfunctions in the hydraulic cylinder and its components. Therefore this study aims to repair the performance of hydraulic cylinder after corrosion and determine the best ways for the reconstruction and maintenance of hydraulic cylinder. Also, to study of the electroplating of internal surface of hydraulic cylinder, which is supposed to raise the economic life of the cylinders and consequently the economic life of machine. The studied factors were:(a) treating the surface of cylinder (before treatment, turning, polishing, chromium electroplating) and measuring the force needed to move the piston in the presence of three kinds of oils  ( ISO VG numbers are VG32 ,VG22 and VG10 ) as hydraulic liquids and (b) the effect of piston  on the cylinder performance (without pressure ring, with one pressure ring and with two pressure rings) after each treatment on the cylinder surface, to evaluate the effect of the previous factors on the cylinder performance (measured by the specific force needed to move piston).. The final data indicated that electroplating of the inner surface of the hydraulic cylinder resulted in improving the performance of the hydraulic cylinder. 
References
Casey, B. 2002. Hydraulic problems and maintenance. Inside Hydraulics

      newsletter. Eaton Hydraulics limited, USA. Views at

                             www.Insider-hydraulic.com

Casey, B. 2006. Hydraulic problems and maintenance. Inside Hydraulics

     newsletter. Eaton Hydraulics limited company, USA. Views at

                             www.Insider-hydraulic.com.

Whitlock, J. 2003. Hydraulic problems and maintenance. Inside 

       Hydraulics newslette2003r. Eaton Hydraulics limited,USA. Views at  www.Insider-hydraulic.com .

MacNab, M . 1984. Choosing the right hydraulic cylinder Power.

        Farming-Magazine. 93(9): 20, pages 22-23.

Fras, J. 1986. Investigation of metal coatings used in regeneration of

        hydraulic parts of combine harvesters. Zeszyty-Naukowe-Akademii-

        Rolniczej-w-Szczecinie, Rolnictwo .

Fras,J. and S. Nieckol. 1985. Study of hydraulic cylinder wear in

         combine.Zeszyty-Naukowe-Akademii-Rolniczej-w-Szczecinie,-

         Rolnictwo, 38(117): 11-18.

Omar, E. 2005. Electroplating of metals and plastic (textbook)

    Pages 122-170. EL-Elmiya Library Cairo.

Statistics
Article View: 209
PDF Download: 332