The effect of twist multiplier on the tear strength of woven fabrics | ||
| International Design Journal | ||
| Article 22, Volume 11, Issue 3 - Serial Number 40, May and June 2021, Pages 299-307 PDF (249.55 K) | ||
| Document Type: Original Article | ||
| DOI: 10.21608/idj.2021.162527 | ||
| Author | ||
| Haitham Abdel Daim Mahmoud Ahmed | ||
| Lecturer-Spinning, Weaving, and knitting Department, Faculty of Applied Arts, Damietta University, Egypt, haitham.daim@gmail.com | ||
| Abstract | ||
| Tearing strength is one of the important quality items of finished woven fabrics. It refers to the rupture of a fabric progressively along a line thread by thread. Tearing strength mainly depends on fibre, yarn and fabric characteristics along with mechanical and chemical finishing treatments given to the fabric. From an industry point of view, studying this fabric characteristic is an essential and urgent step because it reflects the endurance extent of the end textile structure. The main objective of this investigation is to examine the effect of twist multiplier (4.1, 4.4 and 4.7) on weft/warp tear strengths for fabric samples of cotton/polyester blend (50:50) using carded and combed spun yarns. In addition, three weft densities being 18, 22 and 25 were also applied. Results exhibited that the weft/warp tearing strengths are negatively responded to the increase of twist multiplier and weft density for the two spinning systems. In some cases, the weft-way and warp-way warp tearing strengths may be decreased with increasing twist multiplier to a certain extent and then slightly decreased or constant. On the other hand, it is observed that weft/warp tearing strength values for the fabrics made of combed spun yarns were very close to their corresponding values for carded spun yarns under most tested treatments. | ||
| Keywords | ||
| fabric structure; tearing strength; twist multiplier; weft density | ||
| References | ||
|
1. Abou-Nassif, G.A. (2012). Effect of weave structure and weft density on the physical and mechanical properties of micropolyester woven fabrics, Journal of American Science, 9(3): 1326-1331.
2. Abou-Nassif, G.A. (2014). Comparative study between physical properties of compact and ring yarn fabrics produced from medium and coarser yarn counts. Journal of Textiles, 1-6.
3. Almetwally, A. A. and Mona. M. Salem (2010). Comparison between mechanical properties of fabrics woven from compact and ring spun yarns. AUTEX Research Journal, Vol. 10 (1): 35-40.
4. Dhamijaa, S. and M. Chopra (2007). Tearing strength of cotton fabrics in relation to certain process and loom parameters. Indian Journal of Fibre & Textile Research Vol. (32) : 439-445.
5. Eltayib, H.E.; A.H.M. Ali and I.A. Ishag (2016). The Prediction of Tear Strength of plain weave fabric Using Linear Regression Models. International Journal of Advanced Engineering Research and Science (IJAERS). Vol. 3 (11): 151-154.
6. Eman Eltahan (2018). Structural parameters affecting tear strength of the fabrics tents. Alexandria Engineering Journal, 57: 97–105.
7. Eryuruk, Selin H. and Fatma Kalaoğlu (2015). The effect of weave construction on tear strength of woven fabrics. AUTEX Research Journal, Vol. 15 (3): 207-214.
8. Kotb N.; A. El Geiheini; A. Salman and A. Abdel –Samad (2009). Engineering of Tearing Strength for Pile Fabrics. Journal of Textile and Apparel Technology and Management, Vol. 6 (1): 1-8.
9. Minitab IN. Minitab 16 statistical software. State College: Minitab, Inc.; 2010.
10. Scelzo, W. A.; Backer, S. & Boyce, C., (1994 a). Mechanistic role of yarn and fabric structure in determining tear resistance of woven cloth - Part I: Understanding tongue tear. Textile Research Journal, Vol. 64, No. 5: 291-304.
11. Scelzo, W. A.; Backer, S. & Boyce, C., (1994 b). Mechanistic role of yarn and fabric structure in determining tear resistance of woven cloth. Part II: Modelling tongue tear.Textile Research Journal, Vol. 64, No. 6: 321-329.
12. Snedecor, G.W. and W.G. Cochron (1989). Statistical Methods. 8th Ed., Iowa State Univ. Press, Ames Iowa, USA.
13. Steel, R.; J. Torrie and D. Dicky (1997). Principles and Procedures of Statistics; A Biometrical Approach. 3rd
14. Teli, M.D.; A.R. Khare and R. Chakrabarti (2008). Dependence of yarn and fabric strength on the structural parameters. AUTEX Research Journal, Vol. 8, No. 3: 63-67.
15. Wang, P.; M. Qian; S. Baozhong; H. Hong and G. Bohong (2007). Finite element modeling of woven fabric tearing damage. Textile Research Journal, 81(12): 1273–1286. | ||
|
Statistics Article View: 449 PDF Download: 368 |
||
