MODELLING OF HEAT AND MASS BALANCE OF PRECONDITIONING AND EXTRUSION STAGES FOR FLOATING FEED PRODUCTION | ||
| Misr Journal of Agricultural Engineering | ||
| Article 10, Volume 39, Issue 1, January 2022, Pages 153-172 PDF (1.27 M) | ||
| Document Type: Original Article | ||
| DOI: 10.21608/mjae.2021.89632.1040 | ||
| Authors | ||
| I. S. F. Eladly1; A. H. Bhansawy2; S. A. Ali2; E. G. Khater* 3 | ||
| 1Assist. Lect., Ag. Eng. Dept., Fac. of Ag., Benha U., Egypt. | ||
| 2Prof. of Ag. Eng., Ag. Eng. Dept., Fac. of Ag., Benha U., Egypt. | ||
| 3Assoc. Prof. of Ag. Eng., Ag. Eng. Dept., Fac. of Ag., Benha U., Egypt. | ||
| Abstract | ||
| The main aim of this research was to develop a mathematical model of heat and mass balance of pre-conditioning and extrusion stages to predict the temperature, moister content and energy requirement of the feed production at different heating temperatures and feeding rates. To achieve that, the effect of temperature and mass flow rate of water and oil in preconditioning on energy rate of preconditioning, mass flow rate of production, mass fraction of moisture of production, and energy rate of product were studied. The results indicate that the energy rate of preconditioning ranged from 523.4 to 8164.7 kJ h-1 and 209.4 to 3266.3 kJ h-1 for water and oil, respectively, the energy rate carried by water injection into extruder increased from 352.5 to 916.5 kJ h-1. The mass flow rate of production increased from 144 to 174, 133 to163 and 119 to179 kg h-1 for water, oil and water and oil, respectively. The mass of moisture of production ranged from 0.2 to 0.34, 0.32 to 0.26, and 0.24 to 0.3 kg h-1 for water, oil and water and oil, respectively. The temperature of product ranged from 159 to 174, 180 to163 and 185 to179 °C for water, oil and water and oil, respectively. The energy rate of product ranged from 52590 to 60795.3, 54616 to 57672.9 and 50708.2 to 61970.3 kJ h-1 when the temperatures increased from 25 to 65°C, respectively, at 5 and 30 kg h-1 mass flow rate. | ||
| Keywords | ||
| Heat balance; Mass balance; Mathematical model; Preconditioning; Extrusion; Energy rate; Water; Oil; Mass flow rate; Temperature | ||
| References | ||
|
Dhanasekharan, K.M. and Kokini J.L. (2003). Design and scaling of wheat dough extrusion by numerical simulation of flow and heat transfer. J. Food Eng., 60, 421–430.
Jian, R.R., Yang W.M., Cheng L.S. and Xie P.C. (2017). Numerical analysis of enhanced heat transfer by incorporating torsion elements in the homogenizing section of polymer plasticization with the field synergy principle. Int. J. Heat and Mass Transfer, 115, 946–953.
Jian, R.R., Yang W.M., Cheng L.S. and Xie P.C. (2018). Numerical Simulation on the Enhanced Mixing of Polymer Melt by Single Screw with Torsion Elements in the Homogenizing Section. Polym.-Korea, 42, 910–918.
Kaddour, O. (2018). Factors affecting the floating aquatic feed pellets quality. Misr J. Ag. Eng., 35 (3): 1019 - 1038.
Kannadhason, S., Muthukumarappan K. and Rosentrater K.A. (2011). Effect of starch sources and protein content on extruded aquaculture feed containing DDGS. Food Bioprocess Technol. 4, 282–294.
Kuzyaev, I.M. (2005). Intensification of Heat and Mass Transfer Processes in the Working Channel of Extrusion Machines during Processing of Newtonian Polymer Liquids. Heat Transf. Res., 36, 359–371.
Lundblad, K., Hancock J., Behnke K., McKinney L., Alavi S., Prestlokken E. and Sorensen M. (2012). Ideal digestibility of crude protein, amino acids, dry matter and phosphorous in pigs fed diets steam conditioned at low and high temperature, expander conditioned or extruder processed. Anim. Feed Sci. Technol. 172, 237–241.
Lwis, L.L., Stark C.R., Fahrenholz A.C., Bergstrom J.R. and Jone C.K. (2015). Evaluation of conditioning time and temperature on gelatinized starch and vitamin retention in a pelleted swine diet. J. Anim. Sci. 93, 615–619.
Magliano, R. (2007). Aqüicultura: grande aliada? Faces e Interfaces. Available in: http://www.olharvital.ufrj.br/2006/index.php?id_edic ao=067&codigo=4. Accessed on: 10/06/09.
Martin, A., Raffael O., Alexander G., Heike P.K. and Azad E. (2019). Effect of rapeseed press cake and peel on the extruder response and physical pellet quality in extruded fish feed. Aquaculture, 512: 734316.
Monchatre, B., Raveyre C. and Carrot C. (2018). Influence of the melt viscosity and operating conditions on the degree of filling, pressure, temperature, and residence time in a co-kneader. Polym. Eng. Sci., 58, 133–141.
Naga K., Romano N., Ebrahimi M., Amin S.M.N., Kamarudin M. S., Karami A. and Kumar V. (2018). Improvement of feed pellet characteristics by dietary pre-gelatinized starch and their subsequent effects on growth and physiology in tilapia. Food Chemistry 239 (2018) 1037–1046.
Navale, S.A., Swami S.B. and Thakor N.J. (2015). Extrusion Cooking Technology for Foods: A Review. Journal of Ready to Eat Food, 2(3): 66 - 80.
Pacheco, A.C.W., Gianini R.L., Paulo E.P., Luiz M.D.J. and Paulo R.P. (2011). Modeling of drying and adsorption isotherms of the fish feed. Brazilian archives of biology and technology, Brasil.
Park, B.C., Shinjin, Co., Ltd and Seoul (2013). Effects of extruded and extruded-pelleted corn products partially substituted for unprocessed corn of the starter diet on growth performance and incidence of diarrhea in weanling pigs. J. Anim. Sci. Technol. 55, 109–113.
Riaz, M.N. (2000). Extruders in food applications. CRC press is an imprint of Taylor and Francis Group. http://www.crcpress.com.
Schoeff, R.W. (1994). History of the Formula Feed Industry. In: R.R. McEllhiney, Ed. Feed Manufacturing Technology IV. American Feed Industry Association. Arlington, Virginia: 7.
Selle, P.H., Liu S.Y., Cai J. and Cowieson A.J. (2013). Steam-pelleting temperatures, grain variety, feed form and protease supplementation of medially ground, sorghum-based broiler diets: influences on growth performance, relative gizzard weights, nutrient utilization, and starch and nitrogen digestibility. Anim. Product. Sci. 53, 378–387.
Singh, R.P. and Heldman D.R. (2009). Introduction of food engineering. Fourth edition. Elsevier. Chaina.
Spina, R., Spekowius M. and Hopmann C. (2017). Simulation of crystallization of isotactic polypropylene with different shear regimes. Thermochim. Acta, 659, 44–54.
Teixeira, C., Gaspar-Cunha A. and Covas J.A. (2012). Flow and heat transfer along the length of a co-rotating twin screw extruder. Polym.-Plast. Technol. Eng., 51, 1567–1577.
Tumuluru, J.S., Wright C.T., Hess J.R. and Kenney K.L. (2011). A review of biomass densification systems to develop uniform feedstock commodities for bioenergy application, Biofuels Bioprod. Biorefin. 5, 683–707.
Wang, C., Bussmann M. and Park C.B. (2010). Numerical Investigation of the Effect of Screw Geometry on the Mixing of a Viscous Polymer Melt. J. Appl. Polym. Sci., 117, 775–784. | ||
|
Statistics Article View: 434 PDF Download: 783 |
||
