Influence of using Straight and Twisted Elliptical Section Heater Tubes on Stirling Engine Performance | ||
| JES. Journal of Engineering Sciences | ||
| Article 6, Volume 50, Issue 6, November 2022, Pages 11-30 PDF (1.5 M) | ||
| Document Type: Research Paper | ||
| DOI: 10.21608/jesaun.2022.150787.1155 | ||
| Authors | ||
| Ahmed Abdelnaby Abdelhameed* 1; Saleh Abo-Elfadl Ahmed1; Othman Hassan Othman2; Abdel Moneim Mahmoud Ibrahim1 | ||
| 1Power Mechanical Engineering Department,Faculty of engineering,Assiut university.Assiut city,Egypt | ||
| 2Power Mechanical Engineering Departmentt,Faculty of engineering,Assiut university.Assiut city,Egypt | ||
| Abstract | ||
| The heat transfer area of the heater tubes is a significant factor that deeply affects net output power and thermal efficiency in Stirling engines. It is greatly affected by the input heat transfer rate, heater tube geometries, and heat transfer removal rate. The alpha Stirling engine heater is our concern in this study. An ordinary circular and straight elliptical section heater tubes having different twisting ratios with a rectangular section-connecting duct are used to study the different heater tube configurations and twisting effect on the heat transfer characteristics and working fluid motion inside the engine. Three twisting ratios of two, three, and four with each section of the heater tube are used in this study. The 3D simulation model using the SST K-ω model using ANSYS FLUENT-16 is used for simulating airflow through the hot cylinder, heater tubes, regenerator, cooler, and cold cylinder of the Stirling engine, during a complete engine cycle. The results showed that increasing the twisting value increases the net output power and the thermal efficiency. The maximum net power output occurs at the elliptical section heater tube with a two-twist ratio with a value of 1249.26 W by an increase of 86.90 W with respect to the ordinary circular heater. In addition, the maximum thermal efficiency occurs at the elliptical section heater tube with a two-twist ratio with a value of 29.55% by an increase of 1.07% with respect to the ordinary circular heater. | ||
| Keywords | ||
| Stirling engine; Heater tubes; Elliptical; Twist ratio; Thermal effeciency | ||
| References | ||
|
References
[1] D. Litalien et al., “A low teperature Differential stirling engine foe power generation,” Bifurcations, vol. 45, no. 1. pp. 1–19, 2009, [Online]. Available: http://dx.doi.org/10.1016/j.refiri.2017.07.010%0Ahttp://coop-ist.cirad.fr%0Ahttp://www.theses.fr/2014AIXM5048%0Ahttp://www.cairn.info/revue-management-et-avenir-2010-6-page-84.htm%0Ahttp://www.cairn.info/bifurcations--9782707156006-page-349.htm%0Ahttp://w.
[2] Z. Bao-sheng, C. Ning, and S. Zheng-chang, “New technology for coalbed methane power generation based on Stirling engine driven by porous burner,” Procedia Earth and Planetary Science, vol. 1, no. 1. pp. 1480–1483, 2009, doi: 10.1016/j.proeps.2009.09.228.
[3] C. H. Cheng and Y. J. Yu, “Numerical model for predicting thermodynamic cycle and thermal efficiency of a beta-type Stirling engine with rhombic-drive mechanism,” Renewable Energy, vol. 35, no. 11. pp. 2590–2601, 2010, doi: 10.1016/j.renene.2010.04.002.
[4] M. Tarawneh, F. Al-Ghathian, M. A. Nawafleh, and N. Al-Kloub, “Numerical Simulation and Performance Evaluation of Stirling Engine Cycle,” Jordan Journal of Mechanical and Industrial Engineering, Vol. 4, November 2010.
[5] M. H. Ahmadi, M. A. Ahmadi, M. Mehrpooya, and M. A. Rosen, “Using GMDH neural networks to model the power and torque of a stirling engine,” Sustainability (Switzerland), vol. 7, no. 2. pp. 2243–2255, 2015, doi: 10.3390/su7022243.
[6] A. Chmielewski, S. Radkowski, R. Gumiński, and P. Szulim, “Experimental research and application possibilities of microcogeneration system with Stirling engine,” Experimental research and application possibilities of microcogeneration system with Stirling engine, vol. 95, no. 1. pp. 14–22, 2015.
[7] B. Hoegel, “Thermodynamics-Based Design of Stirling Engines For Low-Temperature Heat Sources” Ph.D. thesis, Mech. Dep., University of Canterbury, New Zealand, 2014.
[8] C. Alvarez-Herrera, A. R. Moreno-Nieto, and J. G. Murillo-Ramírez, “Study of temperature distribution over a Stirling engine by using the schlieren technique,” Emerging Challenges for Experimental Mechanics in Energy and Environmental Applications, Proceedings of the 5th International Symposium on Experimental Mechanics and 9th Symposium on Optics in Industry (ISEM-SOI),2015, DOI centre 10.1007/978-3-319-28513-9.
[9] Ke Li et al., “Analysis of Stirling engine heater head with liquid NaK for heat transportation,” Research Gate, 2012, [Online]. Available: https://www.researchgate.net/publication/291299162.
[10] H. Karabulut, H. Solmaz, and F. Aksoy, “A numerical study for Stirling engine heater development,” Heat Transf. Res., vol. 48, no. 6, pp. 477–498, 2017, doi: 10.1615/HeatTransRes.2016011033.
[11] D. Thombare, S. P. Kumbhar, D. G. Thombare, and N. K. Chhapkhane, “CFD Simulation of Stirling Engine Heater,” International Journal of Engineering & Science Research, vol. 3, pp. 3077–3084, 2013, [Online]. Available: www.ijesr.org.
[12] T. Akazawa, K. Hirata, T. Hoshino, H. Kita, and K. Fujiwara, “Design of Ceramics Heater for Stirling Engine,” Icdes. 2014.
[13] K. Kumar and B. T. Kuzhiveli, “Parametric investigation of the hybrid regenerator of a Stirling cryocooler. ” Indian Journal of Cryogenics, vol. 41, pp. 81-85, (2016).
[14] S. K. Andersen, H. Carlsen, and P. G. Thomsen, “Numerical study on optimal Stirling engine regenerator matrix designs taking into account the effects of matrix temperature oscillations,” Energy Convers. Manag., vol. 47, no. 7–8, pp. 894–908, May 2006, doi: 10.1016/j.enconman.2005.06.006.
[15] R. Gheith, F. Aloui, and S. Ben Nasrallah, “Study of the regenerator constituting material influence on a gamma type Stirling engine,” J. Mech. Sci. Technol., vol. 26, no. 4, pp. 1251–1255, Apr. 2012, DOI: 10.1007/s12206-012-0218-9.
[16] C. P. Speer, D. A. Miller, C. J. A. Stumpf, J. P. Michaud, and D. S. Nobes, “Modification of an ST05G-CNC stirling engine to use a low temperature heat source,” 15th International Energy Conversion Engineering Conference, 2017. 2017, doi: 10.2514/6.2017-4793.
[17] S. Alfarawi, R. AL-Dadah, and S. Mahmoud, “Influence of phase angle and dead volume on gamma-type Stirling engine power using CFD simulation,” Energy Convers. Manag. 124, pp. 130–140, 2016.
[18] M. A. Mohammadi, A. Jafarian “CFD simulation to investigate hydrodynamics of oscillating flow in a Beta-type Stirling engine”, Energy, Volume 153, 15 June 2018, Pages 287-300, Doi.org/10.1016/j.energy.2018.04.017 .
[19] L. Kuban, J. Stempka, A. Tyliszczak, “A 3D-CFD study of a γ-type Stirling engine”, Energy, Volume 169, 15 February 2019, Pages 142-159, doi.org/10.1016/j.energy.2018.12.009 .
[20] Wandong Zhao, Ruijie Li, Hailing Li, Ying Zhang, Songgang Qiu, "Numerical analysis of fluid dynamics and thermodynamics in a Stirling engine", Applied Thermal Engineering, 189 (2021) 116727, Doi.org/10.1016/j.applthermaleng. 2021.116727. [21] ANSYS FLUENT User’s Guide, chapter 7: Porous Media Conditions, Release 16.0 © ANSYS, Inc. January 2015 [22] S.C. Costa, I. Barrino, M. Tutar, J.A. Esnaola, H. Barrutia, "The thermal non-equilibrium porous media modeling for CFD study of woven wire matrix of a Stirling regenerator," Energy Convers. Manage. 89 PP. 473–483, 2015. | ||
|
Statistics Article View: 462 PDF Download: 808 |
||
