Modeling and Analysis of LiNbO3 Optical Modulator with Two Step Back Slot Structure | ||
| Menoufia Journal of Electronic Engineering Research | ||
| Article 5, Volume 22, Issue 1, January 2012, Pages 33-43 | ||
| Document Type: Original Article | ||
| DOI: 10.21608/mjeer.2012.66906 | ||
| Authors | ||
| Ahmed A. Abou El-Fadl; Mahmoud A. Wafa | ||
| Faculty of Engineering, King Abdulaziz University, Rabigh, K.S.A | ||
| Abstract | ||
| A numerical model of x-cut LiNbO3 optical modulator with a two step back slot structure to satisfy the velocity matching condition without the layer of silicon dioxide is presented. The analysis is based on the method of transverse technique. An equivalent circuit is deduced to represent the structure. Generalized trial quantities are introduced as virtual adjustable sources in the equivalent network representation of boundary conditions. The lossy conductor of a planar transmission line is represented by a particular two port network. Thus, metallic losses can be evaluated for any metallization thickness without restricting the conductor modeling to a simple surface impedance approximation. The dependence of the effective microwave index, the characteristic impedance and the product of the drive voltage and the electrode interaction length on the thickness of substrate near the ground electrode has been investigated. The optical response of the modulator is also evaluated. This modulator is sufficient to 40 Gb/s optical transmission systems. | ||
| References | ||
|
[1] Noguchi, K. et al., "40Gbit/s Ti:LiNbO3 optical modulator with a two-stage electrode," IEICE Trans. Electron., E81-C, (8), pp. 1316-1320, 1998.
[2] Burns, W. K. et al., "Low drive voltage, broadband LiNbO3 modulators with and without etched ridges," J. Lightwave Technol., 17, (12), pp. 2551-2555, 1999.
[3] Madabhushi, R. et al., "Wide band, low drive voltage Ti:LiNbO3 optical modulators for 40 Gbit/s applications," ECOC'98, Tech. Dig., Madrid, Spain, pp.547-548, 1998.
[4] H. Miyazawa, et al., "DC drift phenomena of LiNbO3 optical modulator," in Proc. IEICE'94, Paper SA-9-3, 1994.
[5] S. K. Korotky and J. J. Veselka, "Rc network analysis of long term Ti: LiNbO3 bias stability," J. Lightwave Technol., vol. 14, pp. 2687-2697, 96.
[6] Nagata H., " DC drift failure rate estimation of 10 Gb/s X-cut lithium niobate modulators," IEEE Photonics Technol. Lett., 12, (11), pp. 1477-1479, 2000.
[7] Hallemeler, P. et al., "Next generation 10 Gb/s lithium niobate modulator components for RZ based transmission technique, "Proc. NFOEC'99, Chicago, IL, USA, pp. 26-30, 1999.
[8] Minakata, M. and Goto, M., "The perfect velocity matched high speed LiNbO3 optical modulators with backside slot," JICAST'98/CPST'98, Conf. Pub., Japan, 1998.
[9] J. Kondo et al., "High-speed and low driving voltage X-cut LiNbO3 optical modulator with two step backside slot," Electron. Lett., vol.38, no.10, pp.472-473, May 2002.
[10] Ahmed A. Abou El-Fadl, A. Zarea and O. M. Ba-Rukab, “Modeling and analysis of broadband LiNbO3 optical modulators with a ridge structure ,” Proc. of the 2000 IEEE Canadian Conference on Electrical and Computer Engineering, CCECE 2000, World Trade and Convention Center, Halifax, Nova Scotia , Canada, May 7-10, 2000.
[11] Ahmed A. Abou El-Fadl, K. A. Mostafa, T. E. Taha, and A. A. Aboul-Enien, “Electrode-source characteristic impedance match of CPW for LiNbO3 optical modulators with and without ridge structure ,” Proc. of the 1 8th National Radio Science Conference, NRSC’2001, D7, Feb. 27-29, Faculty Engineering, Mansoura University, EGYPT, 2001. | ||
|
Statistics Article View: 129 |
||
