A Comparative Study on Manual And computerized 3D Programs In Drawing Flat Pattern For Female Trousers | ||
| International Design Journal | ||
| Article 21, Volume 8, Issue 1 - Serial Number 25, January 2018, Pages 243-253 PDF (1.15 M) | ||
| Document Type: Original Article | ||
| DOI: 10.21608/idj.2018.86306 | ||
| Authors | ||
| Fedaa Khedr Ibn Khalid Farag1; Rania Mostafa Kamel Abdelaal Debes2; Shadia Salah Hasan Metwali Salim2 | ||
| 1Faculty of Home Economics-Department of Clothes and Textile-King Abdul-Aziz University in Jeddah | ||
| 2Associate professor at the Department of Clothes and Textile- Faculty of Home Economics - King Abdul-Aziz University in Jeddah | ||
| Abstract | ||
| Clothes industry is considered one of the most important industries. It enjoys a non-stop development due to the rapid development in the social and economic life. Thus, producers and researchers of clothes compete to avail the necessary factors to produce such industry (Managi, 2005, p.1). Due to such development ,which has taken place at the start of the twentieth century, that has covered all aspects of life, the need to apply a scientific method in designing clothes, such a process that precedes the process of cutting and tailoring clothes that should produce stable and guaranteed results, has been one of the key requirements of our era. Therefore, our era is characterized with rapid change and innovation in women's fashion and clothes styles . Objectives: Using the 3D programs in producing the basic model of women's clothes for (40-44-48) sizes. Measuring the effectiveness of using the 3D programs in reducing the production time of the basic model of women's trousers compared to the manual method. Measuring the effectiveness of the use of the 3D programs in reducing the cost of producing the basic model of women's trousers compared to the manual method. Methodology of the study: In this study, the researcher relied mainly on the experimental approach that targeted conducting a comparative study of two methods of implementing the flat model for women's trousers; they are the traditional method of modeling, the flat method and the method of using modern programs in the fashion industry field "3D programs". Eventually, arbitration of models was carried out by the specialists using the estimation scale to achieve the objectives of the research and verifying its hypotheses. Sample of the research: Sample of the research comprised 12 working women, six of them are working at Tabook University and the other six are working at King Abdul-Aziz University. Results: There were statistically significant differences at (0.05) function level between the two average control ratios in women's trousers implemented by the manual method and the 3D program, for the front, side and back axes. Such differences were in favor of the women's trousers implemented by the 3D program. The improvement rates in women's trousers (front, side and back) implemented by the 3D program ranged from 17.78 to 20.45. There were statistically significant differences at (0.05) function level between the two average control ratios in women's trousers general form, implemented by the manual method and the 3D program. Such differences were in favor of women's trousers general form implemented by the 3D program. The improvement rate in women's trousers general form implemented by the 3D program was 21.93. There were statistically significant differences at (0.05) function level between the two average control ratios in women's trousers implemented by the 3D program and the modified 3D program, for the front, side and back axes. Such differences were in favor of women's trousers implemented by the modified 3D program. | ||
| Keywords | ||
| Models; Flat Pattern; 3D Programs; Female Trousers | ||
| References | ||
|
1- بخاری، أسماء .(2009). تصمیم نماذج تلائم صناعة الملابس الجاهزة للمرأة الحامل فی المملکة العربیة السعودیة. رسالة ماجستیر، جامعة أم القرى، السعودیة. 2- زکی، سهام وعبد اللطیف، سوسن (2003) تخطیط وإنتاج صناعة الملابس (ط1). القاهرة: عالم الکتب. 3- السمان، سامیة إبراهیم .(1997). موسوعة الملابس (ط1). الإسکندریة: نشر کلیة الزراعة. 4- عبد السلام، إیمان والزفتاوی، حنان وشکری، نجوى ومحمود، منى .(2003). التشکیل على المانیکان بین الأصالة والحداثة (ط1). القاهرة: نشر عالم الکتب. 5- مناجی، لطیفة سلیمان .(2005). دراسة التعدیلات للباترون الأساسی وبعض التصمیمات المقترحة للأجسام ذات العیوب. رسالة ماجستیر، جامعة جازان، السعودیة. 6- ندا، سوسن عبد اللطیف .(2001). الحاسب فی صناعة الملابس (ط1). القاهرة: نشر عالم الکتب. 7- Chaw Hlaing, E., Krzywinski, S., & Roedel, H. (2013). Garment prototyping based on scalable virtual female bodies. International Journal of Clothing Science and Technology, 25(3), 184-197. 8- Cho, Y., Tsuchiya, K., Takatera, M., Inui, S., Park, H., & Shimizu, Y. (2010). Computerized pattern making focus on fitting to 3D human body shapes. International Journal of Clothing Science and Technology, 22(1), 16-24. 9- Fang, J .(2003). 3D collar design creation. International Journal of Clothing Science and Technology, 15(2), 88-106. 10- Park, J., Kim, D. E., & Sohn, M. (2011). 3D simulation technology as an effective instructional tool for enhancing spatial visualization skills in apparel design. International Journal of Technology and Design Education, 21(4), 505-517. 11- Petrak, S., & Rogale, D. (2006). Systematic representation and application of a 3D computer-aided garment construction method: Part I: 3D garment basic cut construction on a virtual body model. International Journal of Clothing Science and Technology, 18(3), 179-187. Yunchu, Y., & Weiyuan, Z. (2007). Prototype garment pattern flattening based on individual 3D virtual dummy. International Journal of Clothing Science and Technology, 19(5), 334-348. | ||
|
Statistics Article View: 324 PDF Download: 531 |
||
