ENGINEERING PROPERTIES OF GYPSUM COMPOSITE CONTAINING CHROME TANNED LEATHER SHAVING WASTE | ||
| Misr Journal of Agricultural Engineering | ||
| Article 16, Volume 35, Issue 4, October 2018, Pages 1441-1456 PDF (734.2 K) | ||
| Document Type: Original Article | ||
| DOI: 10.21608/mjae.2018.95342 | ||
| Authors | ||
| M. I. Morsy1; A. Nasr2 | ||
| 1Agriculture Engineering department, Faculty of Agriculture, Alexandria University, Egypt. | ||
| 2Wool Production and Technology, Desert Research Center, Cairo, Egypt | ||
| Abstract | ||
| Leather tanning industry produces large amounts of solid wastes. Chrome tanned leather shaving waste (CTLS) is about 20% of these solid wastes, which has not been utilized in Egypt and causing environmental hazards and economic loss. This current work investigates the properties of new gypsum composite materials containing different percentages of CTLS, ranging between 0% and 25%. The physical-mechanical characteristics for prepared composites were determined and the construction morphology was analyzed by scanning electron microscopy (SEM). The experimental results show that significant reductions of composite density (from 2.1 to 1.35 t/m3), compressive strength (from 7.0 to 2.7 MPa), flexural strength (from 4.5 to 2.2 MPa) and thermal conductivity (from 0.60 to 0.19 W/m°C) occurred with increasing CTLS content (from 0 to 25%), respectively. Thermal conductivity of CTLS-gypsum composite especially at high content of CTLS allowed us to use this formulation as a separations or filling materials in buildings to increase the thermal insulation. SEM micrograph of the CTLS-gypsum composite shows homogeneous and complex structures with good interaction between CTLS and gypsum. | ||
| Keywords | ||
| leather tanning; shaving waste; gypsum composite | ||
| References | ||
|
Abebaw, G., and B. Abate. "Chrome tanned leather waste dechroming optimization for potential poultry feed additive source: a waste to resources approach feed for future." J. of Environ. Pollut. amd Manag 1, no. 1 (2018): 1-6.
Abuh N., and Umoh A. "Palm kernel fruit fiber reinforced gypsum-cement based wall panels: it’s physical and mechanical characteristics." Pollution Vol. 1 Issue 02 (2015) :117–126.
Agrawal, A., and V. : B.D., P. Kumar. "Remediation options for the treatment of electroplating and leather tanning effluent containing chromium-a review." Miner Process Extra Metal Rev 27 (2006): 99-130.
ASTM. Books of standards Vol.15.04. USA: American Society for Testing and Materials, 2014.
Bank, World. Pollution Prevention and Abatement-Hand Book. Washington, DC, USA., 1999.
BASF. Pocket book for leather technologist. 4. 67056 Ludwigshafen, Germany: Badische Anilin- und Soda-Fabrik, 2007.
DIN EN 196-1, 2005. Methods of testing cement - Part 1: Determination of strength”, Beuth Verlag, Berlin.
Dutta, S.S. An Introduction to the Principles of Leather Manufacture. 4. India: Indian Leather Techno Association, 2008.
Eylem, K.: Rita, P., and F.I.P. Pere. "Composites from leather industry buffing dust: a review." Annals of the University of Oradea Fascicle of Textiles, Leatherwork 18, no. 2 (2017): 149-154.
FAOSTAT. Production-Crops data. ROME: World Food And Agriculture Organization, 2017.
Giovannoni, Elena, and Giacomo Fabietti. "Chapter 2: What Is Sustainability? A Review of the Concept and Its Applications." In Intgerated reporting concepts and cases that redefine corporate accountability, by C. Busco, M.L. Frigo, A. Riccaboni, & P. Quattrone, 21-40. Springer International Publishing, 2013.
Gudro, Ilze. "Opportunities of Raw Hide Using as a Sustainable Material in Latvia." Scientific Journal of Riga Technical University 3 (2011): 103-107.
Husen, Ahmed, Alebachew Tilahun, Ayichew Teshale, and Tadele Gashaw. "Review on Pre and Post- Slaughter Defects of Hide and Skin in Ethiopia." Advances in Biological Research 10, no. 3 (2016): 154-161.
Kolomaznik, K., M. Mladek, F. Langmaier, D.C. Shelly, and M.M. Taylor. "Closed loop for chromium in tannery operation." J Am Leather Chem Assoc 98, no. 12 (2003): 487–490.
Lakrafli H., S. Tahiri , A. Albizane and M.E. El Otmani. "Effect of wet blue chrome shaving and buffing dust of leather industry on the thermal conductivity of cement and plaster based materials". Construction and Building Materials 30(2012): 590–596.
Pati, A., R. Chaudhary, and S. Subramani. "A review on management of chrome-tanned leather shavings: a holistic paradigm to combat the environmental issues." Environ Sci Pollut Res 21 (2014): 11266-11282.
Ponsubbiah, S., S. Suryanarayana, and D. Sanjeev Gupta. "Composite from Leather Waste." IJLTEMAS 7, no. 3 (2018): 77-80.
Putshaka, D.J., A. Yakubu, A., M. Jauro, and M. H.H. and Kolo. "Effect of alkali and acid concentration in extraction of chromium III from tannery solid waste." American Journal of Chemistry and Application 2, no. 6 (2015): 89-94.
Reddy M. V., K. Ashalatha, and K. Sasi. "Partial Replacement of Fine Aggregate by Tannery Shredded Waste in Concrete." Saudi Journal of Engineering and Technology. Vol-1, Iss-4(2016):149-151.
Saravanabhavan, S., K.J. Sreeram, J.R. Rao, and B.U. Nair. "The three pot solution for chromium, tannins and solid wastes: recovery and reuse technique for spent semi chrome liquor and chrome shaving." J Soc Leather Technol Chem 89 (2005): 111-114.
Sathish Kumar V and Vijayaravind S. "Utilization of Tannery Shredded Waste as Fine Aggregate in Concrete. " International Journal of Engineering Research & Technology. Vol. 4 Issue 04, (2015):484-486.
Selamat M., R. Hashim, O. Sulaiman, M. Kassim, N. Saharudin, O. Taiwo. "Comparative study of oil palm trunk and rice husk as fillers in gypsum composite for building material. " Construction and Building Materials. Vol. 197 (2019) :526–532.
Sethuraman, C., K. Srinivas, and G. Sekaran. "Double pyrolysis of chrome tanned leather solid waste for safe disposal and products recovery." Int J Sci Eng Res 4, no. 11 (2013): 61-67.
Tahiri, S., et al. "Thermal behaviour of chrome shavings and of sludges recovered after digestion of tanned solid wastes with calcium hydroxide." Waste Manag 27 (2007): 89–95.
Zhu et al., "Physical and mechanical properties of gypsum-based composites reinforced with PVA and PP fibers. " Constr. Build. Mater. Vol.163 (2018): 695–705. | ||
|
Statistics Article View: 483 PDF Download: 883 |
||
