ENGINEERING PARAMETERS AFFECTING THE PERFORMANCE OF MEAT GRINDER | ||
| Misr Journal of Agricultural Engineering | ||
| Article 20, Volume 34, Issue 1, January 2017, Pages 347-368 PDF (1.02 M) | ||
| Document Type: Original Article | ||
| DOI: 10.21608/mjae.2017.97124 | ||
| Authors | ||
| Y. S. Awdallah; K. I. Wasfy | ||
| Lecturer of Agric. Eng., Fac. of Agric., Zagazig Univ., Egypt. | ||
| Abstract | ||
| Experiments were carried out to study different engineering parameters affecting the performance of camel meat grinder in order to increase product quality and decrease both energy and cost. The grinder shaft was designed so as to save it from over loads and high stresses. The grinder performance was studied as a function of change in meat mass (250, 450, 650 and 850 g), rotational speed (200, 250, 300 and 380 rpm), die holes diameter (4 and 6mm) and number of blades (4, 6 and 8 blades). Performance was evaluated was in terms of water holding capacity, grinder productivity, required power, energy requirements and grinding cost. The experimental results reveal that the grinder performance was in the optimum region under the following conditions: - The grinder shaft must be designed at a 25 mm diameter. - Operate the grinder at a rotational speed of 300 rpm (0.39 m/s). - The extruding plate was to be 6mm die hole diameter. - The meat mass should be ranged from 450 g to 650 g. - Using 6 blades in the meat grinder. | ||
| References | ||
|
AOAC (1990).Official Methods of Analysis of the Association Chemists, W. Howrtez (ed.) 15th edn.
Awady, M. N. (1978). Tractor and farm machinery. Txt bk., Col. Agric., Ain Shams Uinv.: 146-167.
FAO (2012). Food and Agriculture organization of the United Nations. FAO statistics division. FAO state.
Grau, R. (1960). Fleisch und Fleischwaren. 1.Ed., Berlin Verlag A.W. Hayn´s Erben: 240 p.
Haack, E. and W. Schnaeckel (2008). Vom Rohstoff zum Feinbrat-Ein Arbeitsgang. Trennsysteme zur Aufwertung Stofflicher Eigenschaften von Fleisch-Teil 2, Fleischwirtschaft, 88 (4): 75-80.
Irmscher, S. B; Z. Bojthe, K. Herrmann, M. Gibis, R. Kohlus and J. Weiss (2013). Influence of filling conditions on product quality and machine parameters in fermented coarse meat emulsions produced by high shear grinding and vacuum filling. J. of Food Engineering, 117: 316–325.
Khurmi, R. S. (2005). Machines design. Eurasia Publishing House. Ram Nagar, New Delhi. Pp 4-5, 52-57, 568- 571, 716-719, 728-729, 1012-1015.
Kitun, A. V. and V. I. Perednya (2006). Improving the working indices of a grinder-mixer. Traktory i Sel'skokhozyaistvennye Mashiny; 10, 43-44.
Krickmeier, J; W. Schnackel, W. Pongjanyanukul, D. Schnackel and I. Micklisch (2012). Analysis for optimization of the mincing process: Part 2: Distribution of necessary cutting works in dependence of machinery and raw material influences. Fleischwirtschaft; 92: 1, 88-92.
Kurt, G. (1979). Engineering formulas. Third Ed. Mc Graw-Hill book Company. New York St. Lous San Francisco Montreal-Toronto.
Schnackel, W; J. Krickmeier, D. Oktaviani Schnackel and I. Micklisch (2011). Analysis for optimisation of the mincing process: Part 1: Modelling the terms during the disintegration in meat mincers. Fleischwirtschaft; 91: 7, 83-87.
Soliman, S. N. and M. A. F. Abd El-Maksoud (2001). Performance study of meat chopper. Misr J. Agric. Eng., 18 (1): 131 – 150.
Tkacz, K. (2007). Energy consumption of chosen processes of comminution of meat. Roczniki Instytutu Przemyslu Miesnego i Tluszczowego; 45: 2, 55-61. | ||
|
Statistics Article View: 492 PDF Download: 486 |
||
