DEVELOPMENT OF A FODDER BALES CHOPPER | ||
| Misr Journal of Agricultural Engineering | ||
| Article 6, Volume 33, Issue 4, October 2016, Pages 1255-1272 PDF (804.79 K) | ||
| Document Type: Original Article | ||
| DOI: 10.21608/mjae.2016.97596 | ||
| Authors | ||
| A. A. AL-Gezawe1; S. G. Abd El-hamid1; A. Ghandour2 | ||
| 1Agricultural Mechanization Operations Systems Department, AEnRI, Egypt. | ||
| 2Irrigation Engineering Research Department, AEnRI, Egypt. | ||
| Abstract | ||
| The aim of the present study is to develop, construction and to evaluate the performance a fodder-bales chopper. The developed fodder-bales chopper consists of frame, chopper drum (cutting knives - hammers mills - cutting knives and hammers mills), feeding platform and feeding housing. Theoretical analysis was conducted to estimate the chopper shaft diameters so as to save it from over loads and high stresses. The studied performance factors are chopping-knives drum speeds 560, 750, 850 and 1040 rpm, number of knives is 84 for cutting knives and 77 for hammers and bale types (wheat and rice). The performance of the developed fodder bales chopper was evaluated in terms of average and percentage of cutting length, chopping efficiency, required power, energy requirements and operational cost. The main results can be summarized in the following points. The maximum machine productivity values were (785.5 and 830.7 kg/h), the maximum required power values were (20.86 and 22.64 kW), the maximum chopping efficiency values were (96.8 and 97.4%), the minimum average length of cut values were (2.6 and 1.54 cm). Mminimum operating cost values were 19.1 and 21.5 L.E/ton at wheat straw bale and rice straw bale, respectively by using combined knives with hammers at drum speed of 1040rpm. | ||
| References | ||
|
Barger, E.I.; B.L. Eohl ; W.M. Carleton and E.G. Mckibben (1963). Tractor and their power units. 2nd ed., Wiley and Sons. Inc., New York U.S.A.
Basiouny, M. A., A. E. El-Yamani and A. E. El- Shazely (2015). modifying of a local thresher for chopping crop residues., J. Soil Sci. and Agric. Eng., Mansoura Univ. 6 (1): 143-163.
EL-Eraqi, M. and S. EL-Khawaga (2003). Design and test performance of cutting machine for some crop residues. Misr J. Agric. Eng., 20(1): 85 - 101.
El-Hanfy, E. H. and S. A. Shalby (2009). Performance evaluation and modification of the japanese combine chopping unit. Misr J. Agric. Eng., April: 1021- 1035.
Khader, S. S., (1997). Development of a simple chopper system using the field wastes in small farms. Ph. D. Th., Agric. Eng. Dept., Fac. of Agric., Zagazig Univ.
Mani S, Tabil LG and S. Sokhansanj (2004). Grinding performance and physical properties of wheat and barley straws, corn stover and switchgrass. Biomass and Bioenergy, 27: 339–352.
Mady, M. A., (1999). Developing a manual cutting machine suitable for mechanical cutting stalks. Misr J. Agric. Eng., 16(3):449 - 459.
Tavakoli, H., S. S. Mohtasebi, A. Jafari and D. Mahdavinejad (2009). Power requirement for particle size reduction of wheat straw as a function of straw threshing unit parameters, American Journal of Crop Science.3 (4), pp:231-236.
Von Bargen K, M. Lamb and D. E. Neels (1981). Energy requirements for particle size reduction of crop residue. American Society of Agricultural Engineers, Paper no. 81-4062. St. Joseph, MI, USA.
Yonis, S. M.; T. H. Mohamed; M. I. Ghonimy and M. A. Baiomy (2001). Development of rice straw chopper. Misr J. Agric. Eng., 18(4):173 - 185. | ||
|
Statistics Article View: 293 PDF Download: 361 |
||
