INFLUENCE OF DRUM CHIPPER SETTING ON THE WOOD CHIPS PERFORMANCE | ||
| Misr Journal of Agricultural Engineering | ||
| Article 8, Volume 33, Issue 4, October 2016, Pages 1293-1314 PDF (1013.41 K) | ||
| Document Type: Original Article | ||
| DOI: 10.21608/mjae.2016.97598 | ||
| Authors | ||
| Z. E. Ismail1; M. I. Ghazy2 | ||
| 1Prof. of Power Technology and Machinery, Agric. Eng. Dept., fac. of Agric., Mansoura Univ., Egypt. | ||
| 2Literature of Agric. Eng., Agric. Eng. Dept., fac. of Agric., Mansoura Univ., Egypt. | ||
| Abstract | ||
| Recently, spread in the world many different categories of wood chipper to be convert the field trees waste to chips. In Egypt, especially in the new land farms the wastes of field trees represent an immense problem. For this reason, the wood chipper machine manufactured in small workshops scattered in the region of Dakahlia governorate. Because of the owners of these workshops, do not have experience in the design of wood chipper machines. Therefore, it immediately needed to evaluate each of the chipper design and its operation. Therefore, the aim of recent paper are to evaluate the design of offset slider crank for drum wood chipper and to evaluate operating parameter of drum chipper on wood chip removal rate (WCRR, m3/h), actual chip thickness (ACT), share plan angle (SPA), chip thickness ratio (CTR), chip reduction coefficient (CRC), size classification of wood chips (SCC) and the machine productivity. The operating parameters of the local chipper machine (model MUPM) included two wood sit positions in chipper (perpendicular of wood fiber relative to cutting drum (Per) and parallel to wood fiber (P); two cutting drum revolution (Per1=5000 rpm and Per2= 5500 rpm) two types of wood (white wood or exported and local wood or feedstock) and two moisture content (17% for white wood and 33% for feedstock). | ||
| Keywords | ||
| chipper machine; wood chips; cutting angle; chip thickness; size classification of wood chips | ||
| References | ||
|
Bergander, A. and Salmén, L. (2000). The transverse elastic modulus of the native wood fibre wall. Journal of Pulp and Paper Science: vol.26, No. 6: 234-238.
David, h. Myszka (2012). Machines and mechanisms applied kinematic analysis. Pearson education, inc., publishing as prentice hall, one lake street, upper saddle river, new jersey, 07458.
Gonçalves, R. and Néri A. C. (2005). Orthogonal cutting forces in juvenile and mature pines taeda wood, Sci. Agric. (Piracicaba, Braz.), 62(4), p. 310-318.
Ismail, Z. E. (2004). The first report of project (Developing the metering unite of the pneumatic planter) financed by Mansoura University researches unite.
Ismail, Z. E. (2009). Soil response to tillage treatments. Agricultural Mechanization in Asia, Africa and Latin America (AMA). Vol. 40, No. 4 autumn: 9-14.
Ismail, Z. E. and Abou Habaga, M. M. (2008). Theoretical approach to determine the share dimensions of uproot palm date. Misr. J. Ag. Eng., 25(3): 746-757.
Jernkvist, L. O. and Thuvander, F. (2001). Experimental determination of stiffness variation a cross growth rings in picea abies; Holzforschung Vol. 55, No. 3: 309-317.
Kajberg, J. and Wikman, B. (2007). Viscoelastic parameter estimation by high strain-rate experiments and inverse modeling – Speckle measurements and high speed photography; International Journal of Solids and Structures 44: 145-164.
Kline, W. A.; DeVor R. E. and Lindberg J. R. (1982). The Prediction of cutting forces in end milling with application to cornering cuts. Int. J. Mach. Tool Des. Res., 22 (1), p. 7-22.
Sutherland, J.W. and DeVor, R. E. (1986). An improved method for cutting force and surface error prediction in flexible end milling systems. Journal of Engineering for Industry, 108, p. 269-279.
Svensson, B. A. (2007). Frictional studies and high strain rate testing of wood under refining conditions. Doctoral thesis, Mid Sweden University, Department of Natural science, Sundsvall.
Thuvander, F.; Sjödahl, M. and Berglund, L.A. (2000). Measurement of crack tip strain field in wood at scale of growth rings; Journal of Materials Science 35: 6267-6275.
Tlusty J. S. S., (1991). An overview of modeling and simulation of the milling process. Journal of Engineering for Industry, 1991, 113, p. 169-175.
Toenshoff, H. K. and Denkena, B. (2013). Basics of cutting and abrasive processes. Lecture Notes in Production Engineering, DOI: 10.1007/978-3-642-33257-9_2, Springer-Verlag Berlin Heidelberg.
Uhmeier, A. (1995). Some fundamental aspects of wood chipping; Tappi J Vol. 78, No. 10: 79-86.
Wen-Hsiang Lai, (2000). Modeling of cutting forces in end milling operations. Tamkang Journal of Science and Engineering, 2000, 3(1), p. 15-22.
Zmitrowicz, A. (2006). Models of kinematics dependent anisotropic and heterogeneous friction; International Journal of Solids and Structures, 43(14-15):4407-4451. | ||
|
Statistics Article View: 392 PDF Download: 1,185 |
||
