SOME PHYSICAL AND MECHANICAL PROPERTIES OF JATROPHA FRUITS | ||
| Misr Journal of Agricultural Engineering | ||
| Article 10, Volume 33, Issue 2, April 2016, Pages 475-490 PDF (612.15 K) | ||
| Document Type: Original Article | ||
| DOI: 10.21608/mjae.2016.97971 | ||
| Authors | ||
| R. A. Werby1; Ahmed Mousa2 | ||
| 1Assoc. Prof., Agric. Mach. & Power Eng. Dept., Fac. of Agric. Eng., Al-Azhar Univ., Cairo, Egypt. | ||
| 2Lecturer, Agric. Mach. & Power Eng. Dept., Fac. of Agric. Eng., Al-Azhar Univ., Cairo, Egypt. | ||
| Abstract | ||
| This study was conducted to investigate some physical and mechanical properties of dried Jatropha curcas fruits cultivated in Egypt. The physical and mechanical properties were determined with a moisture content of Jatropha fruit 11.56 (%, d. b.). The results showed that the mean values of the %-ages by weight of fruit parts to whole fruit was 66.24, 33.76, 40.85 and 25.39 % for seeds, shells, kernels and husks, respectively. The results also includes the following properties; length, width, thickness, arithmetic and geometric mean diameter, sphericity, aspect ratio, mass and volume of individual fruit, thousand fruit mass, bulk density, surface area and specific surface area, their averages were found to be 26.84 mm, 20.73 mm, 19.45 mm, 22.34 mm, 22.10 mm, 82.55 %, 77.53 %, 2.61 g, 5.71 cm3, 2552.9 g, 0.304 g/cm3 1539.1 mm2 and 1.82 cm2/cm3, respectively. The mean value of angle of repose was 0.523 rad. For the coefficient of static friction; the galvanized iron sheet surface had the lowest value (0.453) followed by aluminum (0.491) while; the rubber surface had the highest value (0.655). For the rupture forces; the force required for rupturing of fruit in the horizontal loading position (90.56 N) was higher than the force required in the vertical loading position (39.70 N) of the fruit. | ||
| Keywords | ||
| Jatropha fruits; Biodiesel; physical and mechanical properties | ||
| References | ||
|
Awady M. N. and A. S. El-Sayed (1994). Separation of peanut seeds by air stream, (Egypt) Misr J. Ag. Eng., 11(1): 137-147.
Bal S. andH. N. Mishra (1988). Engineering properties of soybean. Proc. Nat. Sem. Soybean Processing and Utilization in India, Bhopal, Madhya Pradesh, India: 146-165.
Cramer J. (2010). The Jatropha handbook from cultivation to application. (Netherlands): 2. (http://www.slideshare.net/QZ1/w1y47) Davies R. M. andD. S. Zibokere (2011).Some physical properties of Gbafilo (Chrysobalanus icaco) fruits and kernels preparatory to primary processing. (Nigeria), Int. J. Agric. Res., 6 (12): 848 - 455.
Dutta S. K., V. K. Nema andR. K. Bhardwaj (1988).Physical properties of gram. (India) J. Agric. Eng. Res. 39: 259 - 268.
EL-Raie A., N. A. Hendawy andA. Z. Taib (1996). A study of physical and engineering properties for some agricultural products. Misr J. Ag. Eng. 13 (1): 211 - 236.
Gonu H., N. Opoku, R. Appiah-Opong, K. Joseph, M. T. Barnor and P. Quarm (2015). Phenotypic traits and chemical properties of Jatropha curcas seeds from northern Ghana. European Scientific Journal, 11(9): 327 - 340. Kabutey A., D. Herák, R. Chotěborský, R. Sigalingging andČ. Mizera (2015).Effect of compression speed on energy requirement and oil yield of Jatropha curcas L. bulk seeds under linear compression, (Czech Republic). Biosys. Eng.; 136: 8 - 13.
Karaj S. andJ. Müller (2010).Determination of physical, mechanical and chemical properties of seeds and kernels of Jatropha curcas L. (Germany), Industrial Crops and Products 32: 129 - 138.
Krishnan P. R. and M. Paramathma (2009). Potentials and Jatropha species wealth of India, Current Science 97(7): 1000-1004. (C. F. Gonu et al. (2015)). Kumar A. and S. Sharma (2008). An evaluation of multipurpose oil seed crop for industrial uses (Jatropha curcas L.): A review. (India), Industrial Crops and Products, 28 (1): 1 - 10. Maduako J. N. and M. O. Faborode (1990).Some physical properties of cocoa pods in relation to primary processing. Ife J. Technol., 2: 1 - 7. (C. F. Sahin & Sumnu (2006)). Mohsenin N. N. (1986).Physical properties of plant and animal materials.Gordon and Breach Sc. Publ., N.Y. Niveditha V. R., K. R. Sridhar and D. Balasubramanian (2013).Physical and mechanical properties of seeds and kernels of Canavalia of coastal sand dunes, (India) IFRJ; 20 (4): 1547 - 1554. Pandey V. C., K. Singh, J. S. Singh, A. Kumar, B. Singh and R. P. Singh (2012).Jatropha curcas: A potential biofuel plant for sustainable environmental development. (India), Renewable and Sustainable Energy Reviews 16: 2870 - 2883 Sahin S. and S. G. Sumnu (2006). Physical properties of foods. USA, Springer, Handbook: 3 - 6. Salawu A. T., M. L. Suleiman andM. Isiaka (2013). Physical properties of Jatropha curcas seed, (Nigeria) EJPAU “Agr. Eng.”; 16 (4), # 07.
Siqueira V. C., O. Resende andT. H. Chaves (2013).Shape and size of Jatropha beans (Jatropha curcas L.) during drying at different temperatures. (Brazil) Rev. Ceres Viçosa; 60 (6): 820 - 825.
Tayle S. A., A. A. EL-Nakib, A. K. Zaalouk and A. N. Ahmed (2011). Some physical properties of apricot pits. (Egypt), Misr J. Ag. Eng., 28(1): 149-165.
Werby R. A., A. K. Zaalouk and S. H. Desoky (2012). Physical and mechanical properties of sweet lupine seeds. (Egypt). The 19th Annual Conference of the Misr Soc. of Ag. Eng.: 687-700.
Yahya A., K. Hamdan , T. A. Ishola and H. Suryanto (2013). Physical and mechanical properties of Jatropha curcas L. fruits from different planting densities. (Malaysia), J. Applied sci., 13 (7): 1004-1012. | ||
|
Statistics Article View: 268 PDF Download: 325 |
||
